Why Does Installation Matter?

At Car and Home Stereo we have been installing exceptional car audio for over 40 years, in fact, when we started there were barely the beginnings of in-car entertainment. Over those years we have seen a tremendous amount of change in the products we use to create outstanding audio experiences. From 8 track cartridge to CD to full digital audio, graphic equalisers to digital signal processors and all the other innovations that have come along we have embraced and utilised these to realise the best possible sound for our customers.

All these fabulous products are available to everybody, there has never been so much choice but all this technology will not guarantee a great sound. That will only be possible with the correct installation and careful setup. Many times I have had a car in that has had a lot of money spent on it yet still sounds bad. From buzzing door panels to downright dangerous wiring I’ve seen it all. Usually from DIY installations but not always. It’s not necessarily the fault of the equipment but rather a combination of poor choice and skimped installation.

It is true that the majority of my work is completely invisible but makes such a massive difference to either the finished sound or the reliability of the whole system.  Application of sound deadening material inside doors will improve the acoustic performance, soldering all connections may take longer but will improve reliability, looming cable runs with fleece tape is expensive but will eliminate any cable rattles and retain the OE look.

It is also important that equipment and wiring are installed to the highest standards to maintain vehicle warranties and safety standards. I have seen microphone cables wrapped around airbags, power cables attached to car batteries without a fuse and any amount of speaker wires dangling over brake pedals. At Car and Home Stereo, we take installation very seriously and we never rush. The best results are not achieved by racing to finish and I would rather spend an extra hour or two to get the best possible sound. After all, you would want your £1000 Rainbow speakers to sound their best.

Of course the same care and attention is applied whether we install top of the range JL Audio speakers or entry level Audison upgrades and in fact, the performance boost from proper door treatment at the lower price range is more apparent.

We will always recommend appropriate enhancements and best installation practices are rigorously followed which may take a little longer and cost a little more but will ultimately lead to a far better sound and is that not what we all really want?

Say Hello To The Future!

JL Audio are a renowned American manufacturer of the highest quality subwoofers, amplifiers and speakers. Some of our best sounding installs have been based around JL Audio products and it is true to say that there is something for everyone within the range.

I was lucky enough to attend a training day with JL Audio’s head of training, Steve Turrisi in March 2017 where, without exaggeration, I was shown the future of car audio. This year JL are launching a fabulous new range of products so let me describe what I was shown.

In June we will see a new entry level speaker range designated C1. These look set to clean up on the simple speaker upgrade market. They are robust, great sounding and very easy to fit as they come with installation collars to cater for different vehicle apertures.



I am sure I will be fitting a lot of these in the near future.

As mentioned there will also be a new ultra high-end speaker set, the C7. This speaker has been designed from the ground up to be the absolute best. Drawing from JL Audio’s many years of experience this will be a milestone in audio performance. It will not be cheap but the best never is.

Expect a price tag in excess of £2000 for these magnificent drivers but I am sure we will not be short of takers when these launch in summer 2017.

Already available are the new RD series of amplifiers which fill the gap between JX and XD. Boasting huge power output from a small chassis I have installed quite a few now and they are extremely impressive.

The RD amps are extremely well priced for the level of performance they deliver, the build quality is amazing and of course, they have the legendary JL sound. Available in mono, 2 channel, 4 channel and the incredible 5 channel every application is catered for.

As if this wasn’t enough I’ve saved the best till last. Available now are the stars of the show. JL Audio’s new line of digital processors the FiX and TwK.

With these products, we will no longer have to endure the sound supplied by factory head units that cannot be swapped out. The BMW, Ford, Audi and VW factory radios can be made to sound amazing. Couple this output to a great amp and speakers and there are no limits to how good your car could sound. This is thanks to the amazing TuN software developed by JL and an installers dream come true.

As can be seen, the software gives me complete control over every aspect of the audio system. There is nowhere near enough room here to describe all the features but trust me, this is a game changer. Car audio will now take the next great performance leap.

For details of all these great new products call me on 01625 432707 or better still call into our shop on Sunderland Street in Macclesfield.


Practicing Safe Sound

There are many ways to upgrade your car audio system and let’s face it, most cars need it. I’m looking at you BMW, VW and Porsche in particular! It is not always possible to upgrade the head unit but it is always possible to improve the speakers. At Car and Home Stereo, we carry speakers by JL Audio, Audison, Hertz, Rainbow and others. This means we can choose the right speaker to suit the car and the customer. We will carefully install your speakers with custom built collars and fittings as well as add sound deadening in the door to improve its acoustic properties. The end result will be a vastly better sound without any cosmetic changes to your car.

And that is where we are finished but before you leave, a word of warning. Please take the time to run your new speakers in. The running in period varies for different speakers but generally, we recommend around 10 hours play time. Running in means keeping the volume at a sensible level without any large bass settings and we will always advise what should be the maximum volume for this period.

If this procedure is not followed your speakers may not fail but they will not reach their full potential, let me explain why.

A speaker is a transducer that converts electrical energy into sound and at the heart of the speaker is a coil of wire sitting inside a magnet. It is bright, shiny copper.

coil speakers good copper

It’s not necessary to know how it works but the important point is that when you pass electricity through a wire heat is generated and the higher the electrical current the more heat is generated. Now, this coil of wire is crucial to the accuracy of the speaker and it is protected by a thin coating of lacquer. This lacquer is quite soft when new and easily damaged by heat but if it is gently warmed over a number of hours the lacquer will harden.

I bet you can see where this is going! If a new speaker is subjected to a lot of power and played loud the voice coil lacquer will boil causing short circuits. Now while this will not necessarily cause the speaker to fail it will mean that the voice coil is not a single continuous wire which leads to a ‘lumpy’ effect within the magnetic gap. This, of course, means that the reproduction of sound is not linear and your investment will not reach its true performance capability. In extreme circumstances, the lacquer is burnt and expands into the magnetic gap which will cause a scratchy sound. These failures are non-reversible, cannot be repaired and are not covered under any warrantee.


coil bad burnt copper

burnt copper coil

So that is why we advise the running in period, to gently warm the voice coil lacquer causing it to cure. This hardened lacquer can now stand the heat of high power and your speakers will really perform as the designers intended.

I cannot overstate the importance of running in, a speaker is more likely to be damaged in the first few hours of use rather than over the rest of its life. At Car and Home Stereo, we want you to get the best possible sound from our expert installation so just hold back on the volume for a few hours, you’ll be glad you did.


Perfect Timing

Let’s talk about sound and specifically how we perceive a sound’s location, (we’ll come back to the elephant in the room). To do this we need to understand what sound is and how it travels.

In its basic form sound is a compression wave propagating through a medium. Think of ripples in water travelling away from where the stone hit. The sound is exactly the same but travelling through air. Travelling very quickly by the way at over 700 miles an hour.

The defining characteristic of a wave is the fact that it has high and low points.


Points along this wave are known as the phase and describe whether the wave is positive or negative and by how much. Now for the clever bit. Consider a listener sat in a chair with their eyes shut, someone off to their left claps. Of course, he can tell it was to his left but how? We all have two ears so it might be true that we can detect the time difference between the sound reaching our left and right ears. But at 700 miles an hour this is a VERY short difference and if true it would mean that all frequencies could be located but as we know the lower the sound the harder it is for us to locate the source.

What we are predominantly detecting is the difference in the phase of the wave between our ears. By measuring the difference between the high and low points on the wave our brains can very accurately calculate sound location and create our spatial awareness. That is why we cannot locate very low (very long wave) sounds as the difference in the phase between our close set ears is minimal (think about thunder).

So now we know this how can we use it in the car audio environments?

One of the big problems in the car is that we are always sat closer to one speaker than the other, therefore the stereo effect is foreshortened to one side. A very crude way to combat this is to put the balance off to one side to compensate but that does not enhance the stereo performance. What we really need to do is place the speakers an equal distance from the listener. Difficult if you are not in a McLaren but we can fool our ears into thinking the sound is coming from somewhere else using phase.

By carefully manipulating the phase of the sound from the speakers we can create the effect that the close speaker is actually further away which leads to a much wider stereo field. This manipulation is very delicate as you can imagine but as a member of the FourMasters network, we are equipped with a sophisticated range of tools and software to achieve this.

The difference between a standard setup and a phase aligned one is astonishing. The whole soundstage comes alive with instruments and vocals spread across the car in a very lifelike and live performance. It is possible to compensate for difficult speaker positioning (BMW) or over separated speakers (VW).

Of course, you will need to have the products to permit this tuning and fortunately, there is a range of sophisticated processors from Audison and Hertz that offer these features. Products like the astonishing Bit family from Audison. These devices give me the capacity to completely shape the acoustic performance in your car which means you will have a completely bespoke sound that perfectly complements your car and your personal tastes.

We have a demonstration vehicle always available at our shop on Sunderland Street in Macclesfield. In this we can demonstrate the difference between a standard and phase aligned sound, we would love to show it off if you want to pop in for an audition.

Oh and the elephant? Elephants communicate their location by stamping on the hard ground. This creates a very low-frequency sound which can travel a great distance. You or I could not locate this low sound but elephants can, why? Because their ears are much further apart and can detect the phase differences!

What To Look Forward To In 2017

It’s good to be back after the festive break and there is a lot to look forward to in 2017.

World renowned audio manufacturer Audison have just announced their new Thesis speaker range. The Thesis amplifier represents the absolute pinnacle of performance without compromise and now there is a speaker set available to match. If you are looking for the absolute best possible sound then this is it.

adison speakers

Staying with Audison, the new slimline Prima subwoofers and enclosures offer stunning bass performance from a very compact form. These will appeal to anyone who does not want to sacrifice much boot space but still demands a Hi-Fi response.

audison prima subwoofers


There will also be a new Prima Pack custom installation kit for the BMW 1 series. This car has always had a very disappointing standard audio system and the Prima Pack is a tailored solution comprising the stunning AP amplifier, a custom Prima speaker pack and compact subwoofer. As with all the Prima Pack systems the factory head unit remains unchanged but the audio performance is greatly enhanced by the AP amplifier. The speakers fit perfectly into the factory locations and the sub is designed to blend seamlessly with the factory trim.

bmw1 car

On the other side of the Atlantic, JL Audio have released their amazing new processors, the new Fix and TwK.

jl audio

The FiX range is simplicity itself to use and automatically deals with all the anomalies inherent in vehicle factory head units. Building on the success of the CleanSweep processor, the FiX can automatically de-equalise audio streams and can even remove spurious time alignment errors giving  a flatter, more open sound from which we can build a better audio system.

The new TwK processors take this a huge step further by allowing access to a vast range of processors via the JL Audio software. From input/output configuration to full spectrum equalisation, this product means that every installation can be tuned to perfection.

Over the break we have been busy building new demonstration stands to showcase some of our best car audio equipment as well as tweaking our Land Rover Discovery demonstrator. This simple car audio system still astonishes me with its clarity and power showing what can be achieved with just one pair of speakers, a subwoofer and amplifier. If you haven’t heard it and can come down to our shop on Sunderland Street in Macclesfield I would encourage you to do so, it is sure to impress.

Our focus, as ever is on installation of the highest quality whether it is a simple dash cam or a full blown custom audio system. We are proud to be a part of the national FourMasters group offering the highest installation standards and a three year warranty on installations.

Please feel free to pop in or give me a call on 01625 432707 to discuss ideas and start your journey towards better sound!

Christmas ’16: In Retrospect

As we come to the end of another trading year it seems fitting to look back at what has changed for us. Personally I think the development of affordable and powerful Digital Signal Processing by Audison has been a complete game changer. At Car and Home Stereo we have always embraced any new technology that will improve the in car audio experience. I can remember fitting Phoenix Gold analogue graphic equalisers in the 90s and spending ages carefully setting them up for the vehicle acoustics. Then the customer’s ‘expert’ mate would have a go, dial in the ‘smiley face’ EQ curve and ruin the sound.

phoenix gold equaliser

When digital systems started to appear I was delighted as there were no more sliders to get fiddled with. I was one of the first to install the Phoenix Gold TiDEQ and it was brilliant if not tearfully expensive. Inevitably, cheaper systems appeared from other manufacturers but they were short on processing power and were distinctly underwhelming.

Fortunately Audison picked up the baton of digital signal processing and ran with it.
audison bit ten d
With powerful software and a host of automatic and manual signal conditioners on board, the Bit range of products now allow me to take any car and be confident of a stunning audio result, regardless of system installed and at a more than reasonable cost.

Another one of my favourite company is JL Audio. Their range of subwoofers and amplifiers are almost unmatched for performance and fidelity. Ten or more years ago we were installing plenty of subs but they were large and needed large enclosures for the best sound. This meant eating up lots of boot space, many customers just did not want that and so compromised on the bass performance. JL Audio, already masters of subwoofer design, set out to help everyone get the best bass performance regardless of available space. In the last couple of years they have produced some spectacular speakers that will operate in almost ridiculously small enclosures. Their TW range particularly so. At Car and Home Stereo sound quality is our first consideration and adding a subwoofer is to my mind essential, now we have the products to allow this regardless of space.

Another product that has really impressed me this year is the SoundTouch 300 soundbar from Bose.
bose sound bar
This very stylish soundbar not only looks fantastic with its black glass top and minimal design but it has a sound that will quite simply amaze. As one of the undisputed leaders in sound reproduction technology Bose have delivered a product that defies reality. Although it is only a single bar it manages to create sound from places far beyond its size. Close your eyes and you will be convinced that there are speakers all round you! If that is not enough then you can also add the optional powerful subwoofer and even wireless rear speakers for a true surround sound experience. Of course it also contains the Bose SoundTouch technology which is just about the best music streaming system available today as the icing on the cake!

And if you are stuck for a last minute Christmas gift, the Bose SoundLink Mini is perfect.
bose mini speaker
Don’t be fooled by the diminutive size of this little Bluetooth player, the sound is amazing. Full portability thanks to its long life rechargeable battery and a rich, full sound whether on its charging cradle or taken on an outing.

All that remains is for us to wish you a happy Christmas and New Year. Here’s looking forward to 2017 and all the exciting developments that are on their way for car and home audio.

Please note that we will be shut for the Christmas holiday from December 25th until January 3rd. Have a happy and musical Christmas!

Something Special

Know someone who’s obsessed with music? Want to surprise them with a new set up? Know absolutely nothing about audio systems?


Why not pop in to Car & Home Stereo? Tim would love to be of service! No one knows sound like Tim and as a musician he understands the importance of it.


That’s why we are bringing you the best from Audison, Alpine, Bose, JL Audio, and many more!

Listening to music with quality speakers is just an extraordinary feeling and there are so many options to choose from in our incredible selection of audio systems, radios and even headphones. We are sure we have something suited for everyone’s taste and we are ready to help you find something be it for you, or a loved one.


Don’t be stranger this Christmas! We’re here on Sunderland Street in Macclesfield and we would be delighted to help you. Please don’t hesitate to call us on 01625 432707.

landrover defender stock

Upgrading the Defender

The Land Rover Defender is a true British classic design. Although, now sadly out of production, the longevity of the Defender means that they will be on (and off) our roads for a great many years to come.

landrover defender stock

It’s design hasn’t changed much in its 70 years and, despite continuous improvements to comfort the audio, performance has always been poor. A relatively noisy environment coupled with small speakers has always meant the sound in the Defender has a lot left to be desired!

As Macclesfield in Cheshire is a fairly rural community there are a lot of these vehicles about as you can imagine and over the years I have developed an audio upgrade package which is powerful and discreet.

The first challenge is the speaker size. Being only 10 cm without modification means that the bass performance is limited. Step forward JL Audio! As the undisputed leaders in subwoofer design, JL Audio are perfectly placed to design speakers that have a much better bass response. This is not to say that a 4 inch speaker can replace a subwoofer but JL Audio’s expertise means that you will get a massive improvement over the stock speaker.

c2 400 subwoofer

To bring the bass response up to the required standard we need to fit in a subwoofer. The irony is that although the Defender is a large utility vehicle, there is almost nowhere to discreetly install a sub box without compromising useful space. JL Audio is here to the rescue, again, with their amazing sub, the 6w3.

jl subwoofer

This astonishing unit is a true 6 inch subwoofer. It is optimized for a tiny enclosure of just 0.125 cu ft. I have developed a carpet trimmed speaker box that will fit just under the roll cage bar behind the front seat. One can be used but for best results we recommend one either side to create an effective 12 inch sub. This allows for a much smoother performance and really blends with the music.


So now we have a sub we are going to need an amplifier. Again, space is limited but fortunately there is room under the driver’s seat for a compact unit. It makes no sense to just amplify the sub so we always install a multi-channel unit to power sub and speakers.

Here we must address the acoustic issues in the vehicle because of the speaker layout and the rather boxy interior of the Defender the sound staging is challenging to say the least. It is essential to install some sort of signal processor or regardless of the quality of the installed equipment, the sound stage will be poor.

I now always use the Audison Prima AP9Bit amplifier. This amazing unit has a full digital signal processor coupled to a powerful 8 channel amplifier in a very compact chassis.


This amplifier can be configured in any way I need depending on the complexity of the installed system. In the Defender it can be a 5 or 6 way for one or two subs. I can then configure the signal processor for the car acoustics and the personal musical tastes of the owner. The software is very powerful, providing  full spectrum equalization on every channel with very fine time alignment available to place the sound stage where it needs to be.

audison speaker amplifier

As a musician I can appreciate the subtleties of sound and this software allows me to bring out the finer details of the music even in a challenging environment like the Land Rover Defender. I am often challenged by owners who say you can’t get a good sound in a Defender but I guarantee that I can. I have installed many of these systems now, both for private individuals and for local dealerships, the feedback is always the same, that they just can’t believe how good this sounds. One customer even came back to tell me that the sound was better than in his Bentley GT!

It is true that the kit described above is extremely good but without the ability to carefully tune it the results would be arable at best. That is where I can make the biggest difference, my experience and exacting standards mean that this great equipment can be enjoyed to its true potential and I feel that this is true value.


Whatever you own, Land Rover, Lamborghini, Lotus or any other car with a challenging audio performance I can make it better, give Tim a call on 01625 432707 or email sales@carhomestereo.co.uk to start your journey to better sound.


Simon Says? Speakers Please!

For this instalment let’s look at speaker installation. The speaker is the last piece of hardware between your music and your ears and as such has an awful lot to do with the sound you hear.

The science behind the speaker is extremely simple; pass an electric current through a wire that sits inside a magnetic field and the wire experiences a force, vary that current and you vary the force. Of course this demonstration produces no sound but if we attach the wire (or coil) to a diaphragm (or cone) we have the nucleus of a working speaker. The electronics in the amplifier produce the varying electrical current and the speaker responds, creating the highly complex vibrations in the air that we hear as music.

The above description is of course highly simplified and in reality there are many more aspects to speaker design. We have to consider the weight of the moving parts, the resistance to movement within the materials themselves, the linearity of the magnetic field, the quality of the coil wire, the damping to prevent uncontrolled excursion, stability of the frame and so on and so on! Fortunately all of these considerations are engineering problems and this means that better engineering will lead to a better product.


When Mr. Ford or Mr. Audi or even Mr. Porsche are told that they have to put speakers in their cars their first consideration is not about quality even when they enlist the help of respected Hi-Fi companies. Their overriding concern is one of reliability. A blown speaker is a warrantee issue and that costs money. The trouble is that a speaker that can survive heavy metal hard core country rap at full volume has to be made super resilient. This speaker is not going to be able to respond to the subtle nuances of any quality musical performance.


At Car and Home Stereo we are always going to install a high quality speaker, carefully selected to match the vehicle and musical tastes of the customer. This is where our installation skills are needed. The average car door is a challenging place for a speaker. It is a steel box that is often wet inside, can be freezing one day and very hot the next. There are moving parts within it and it is subject to a large amount of vibration and noise. Let’s look at a typical installation addressing each point.

First of all we carefully remove the inner trim making sure that all clips and seals are retained. After this the next job is to treat the metal skin with sound deadening material which will absorb road noise and any vibrations within the door.


Particular attention is paid to directly behind the speaker as this will absorb the sound generated by the back of the cone and prevent reflection back into the door panel.

Once the outer skin has been treated we apply a foam barrier to the inner skin. This forms a watertight seal and acts as a thermal and acoustic barrier. This keeps the car warmer in winter, cooler in summer and again reduces road noise. The difference these treatments make to a car is astonishing.


Now we come to installing the speaker. The factory units are often built to fit so we must make panels and collars to allow a perfect fit to the door.


It is very important that no moisture gaps are left as it may come as a surprise to know that doors are designed to let rain flow through them. Any gaps could lead to a wet floor so we make sure everything is sealed with high quality silicone, both the collar and the speaker, this also ensures no air gaps to compromise the speaker performance.


Quite a lot of work but absolutely worth it. These Audison APK speakers sound great anyway but by treating the door they are at least 30% better.

If you would like to know more about how we can improve the sound in your car please call Tim on 01625 432707.

Sharp and Sleek Bose Soundtouch Speakers

We are proud to introduce the latest addition to the Bose Soundtouch family, the Soundtouch 300.
This innovative sound bar offers a level of flexibility and performance that has never been seen before.


















Bose has always been a technology led company and over the years have developed a range of home audio systems that have revolutionised the way we see, and use Hi-Fi.

The Bose Soundtouch platform has taken the wireless, networked audio market to new heights of performance which, coupled with its elegance and simplicity of use has made it the market leader.
The Soundtouch 300 is the first in a new range of home theatre systems that feature amazing performance, stunning looks and an unrivaled feature set.
The new black glass top has been engineered by one of the most famous automotive glass producers in the world while the sleek design draws from years of in house development.

At the heart of the system  is the new sound bar.

















This can connect to your TV via HDMI or optical ensuring complete compatibility.
It contains the now famous Bose AdaptIQ software to ensure the best possible sound in any room regardless of size or shape and once connected to your home internet network you can stream all your music to it via WiFi or Bluetooth.

But of course it doesn’t end there as there are also a couple of optional upgrades.



















If you enjoy the power and performance of modern films you should add the incredible Acoustimass 300 sub. This relatively small unit can be mounted anywhere in the room as it utilises a wireless connection to the sound bar. All it requires is a mains connection. The AdaptIQ software can perfectly integrate the sub into the acoustic environment.

The second optional upgrade is the Acoustimass 300 rear speakers.


















Again these use a wireless connection to the sound bar so no more trailing cables to the back of the room. These will add a true surround sound experience to your movies and music!

This is the first of a whole new range of amazing products from Bose that will once again place it firmly at the top of everyone’s must have list.

At Car and Home Stereo we will be stocking the full range of these systems and we would welcome you for an audition at our showroom on Sunderland Street in Macclesfield, Cheshire.



If you would like to know more, please don’t hesitate to call us on 01625 432707.